Integrated Device Technology (IDT) 54FCT374ATDB

Factory Lead Time

10 Weeks

Contact Plating

Contact plating (finish) provides corrosion protection for base metals and optimizes the mechanical and electrical properties of the contact interfaces.

Lead, Tin

Mount

Through Hole

Package / Case

CDIP

Number of Pins

20

Clock-Edge Trigger Type

Positive Edge

Published

2009

JESD-609 Code

e0

Pbfree Code

no

Part Status

Parts can have many statuses as they progress through the configuration, analysis, review, and approval stages.

Active

Moisture Sensitivity Level (MSL)

1 (Unlimited)

Number of Terminations

20

ECCN Code

EAR99

Terminal Finish

Tin/Lead (Sn63Pb37)

Max Operating Temperature

The Maximum Operating Temperature is the maximum body temperature at which the thermistor is designed to operate for extended periods of time with acceptable stability of its electrical characteristics.

125°C

Min Operating Temperature

-55°C

Packing Method

TUBE

Terminal Position

DUAL

Peak Reflow Temperature (Cel)

240

Number of Functions

1

Supply Voltage

5V

Terminal Pitch

The center distance from one pole to the next.

2.54mm

Reach Compliance Code

not_compliant

Time@Peak Reflow Temperature-Max (s)

NOT SPECIFIED

Pin Count

a count of all of the component leads (or pins)

20

Qualification Status

An indicator of formal certification of qualifications.

Not Qualified

Operating Supply Voltage

The voltage level by which an electrical system is designated and to which certain operating characteristics of the system are related.

5V

Polarity

Non-Inverting

Power Supplies

an electronic circuit that converts the voltage of an alternating current (AC) into a direct current (DC) voltage.?

5V

Temperature Grade

Temperature grades represent a tire's resistance to heat and its ability to dissipate heat when tested under controlled laboratory test conditions.

MILITARY

Max Supply Voltage

In general, the absolute maximum common-mode voltage is VEE-0.3V and VCC+0.3V, but for products without a protection element at the VCC side, voltages up to the absolute maximum rated supply voltage (i.e. VEE+36V) can be supplied, regardless of supply voltage.

5.5V

Min Supply Voltage

The minimum supply voltage (V min ) is explored for sequential logic circuits by statistically simulating the impact of within-die process variations and gate-dielectric soft breakdown on data retention and hold time.

4.5V

Load Capacitance

the amount of capacitance measured or computed across the crystal terminals on the PCB. Frequency Tolerance. Frequency tolerance refers to the allowable deviation from nominal, in parts per million (PPM), at a specific temperature, usually +25°C.

50pF

Number of Ports

A port is identified for each transport protocol and address combination by a 16-bit unsigned number,.

2

Number of Bits

8

Propagation Delay

the flight time of packets over the transmission link and is limited by the speed of light.

7.5 ns

Quiescent Current

The quiescent current is defined as the current level in the amplifier when it is producing an output of zero.

10μA

Turn On Delay Time

Turn-on delay, td(on), is the time taken to charge the input capacitance of the device before drain current conduction can start.

7.2 ns

Family

FCT

Logic Function

D-Type

Output Characteristics

3-STATE

Logic IC Type

BUS DRIVER

Max I(ol)

0.032 A

High Level Output Current

High-level Output Current IOH The current flowing into the output at a specified high- level voltage. Low-level Output Current IOL The current flowing into the output at a specified low- level output voltage.

-12mA

Low Level Output Current

The current into the output terminal with input conditions applied that, according to the product specification, will establish a low level at the output.

32mA

Independent Circuits

1

Length

25.4mm

Width

7.62mm

Thickness

2.9mm

RoHS Status

RoHS means “Restriction of Certain Hazardous Substances” in the “Hazardous Substances Directive” in electrical and electronic equipment.

Non-RoHS Compliant

Lead Free

Contains Lead