Integrated Device Technology (IDT) 74LVC162245APAG8

Factory Lead Time

7 Weeks

Contact Plating

Contact plating (finish) provides corrosion protection for base metals and optimizes the mechanical and electrical properties of the contact interfaces.

Tin

Mount

Surface Mount

Package / Case

TSSOP

Number of Pins

48

Number of Elements

2

Published

2002

JESD-609 Code

e3

Pbfree Code

yes

Part Status

Parts can have many statuses as they progress through the configuration, analysis, review, and approval stages.

Active

Moisture Sensitivity Level (MSL)

1 (Unlimited)

Number of Terminations

48

ECCN Code

EAR99

Max Operating Temperature

The Maximum Operating Temperature is the maximum body temperature at which the thermistor is designed to operate for extended periods of time with acceptable stability of its electrical characteristics.

85°C

Min Operating Temperature

-40°C

Additional Feature

Any Feature, including a modified Existing Feature, that is not an Existing Feature.

WITH DIRECTION CONTROL

Packing Method

TAPE AND REEL

Terminal Position

DUAL

Terminal Form

Occurring at or forming the end of a series, succession, or the like; closing; concluding.

GULL WING

Peak Reflow Temperature (Cel)

260

Number of Functions

2

Supply Voltage

3.3V

Terminal Pitch

The center distance from one pole to the next.

0.5mm

Time@Peak Reflow Temperature-Max (s)

30

Pin Count

a count of all of the component leads (or pins)

48

Operating Supply Voltage

The voltage level by which an electrical system is designated and to which certain operating characteristics of the system are related.

3.3V

Polarity

Non-Inverting

Temperature Grade

Temperature grades represent a tire's resistance to heat and its ability to dissipate heat when tested under controlled laboratory test conditions.

INDUSTRIAL

Number of Channels

16

Max Supply Voltage

In general, the absolute maximum common-mode voltage is VEE-0.3V and VCC+0.3V, but for products without a protection element at the VCC side, voltages up to the absolute maximum rated supply voltage (i.e. VEE+36V) can be supplied, regardless of supply voltage.

3.6V

Min Supply Voltage

The minimum supply voltage (V min ) is explored for sequential logic circuits by statistically simulating the impact of within-die process variations and gate-dielectric soft breakdown on data retention and hold time.

2.7V

Load Capacitance

the amount of capacitance measured or computed across the crystal terminals on the PCB. Frequency Tolerance. Frequency tolerance refers to the allowable deviation from nominal, in parts per million (PPM), at a specific temperature, usually +25°C.

50pF

Number of Ports

A port is identified for each transport protocol and address combination by a 16-bit unsigned number,.

2

Nominal Supply Current

Nominal current is the same as the rated current. It is the current drawn by the motor while delivering rated mechanical output at its shaft.

10μA

Propagation Delay

the flight time of packets over the transmission link and is limited by the speed of light.

4.8 ns

Quiescent Current

The quiescent current is defined as the current level in the amplifier when it is producing an output of zero.

10μA

Turn On Delay Time

Turn-on delay, td(on), is the time taken to charge the input capacitance of the device before drain current conduction can start.

7.1 ns

Family

LVC/LCX/Z

Logic Function

Inverting, Transceiver

Direction

Bidirectional

Output Characteristics

3-STATE WITH SERIES RESISTOR

Logic IC Type

BUS TRANSCEIVER

Number of Bits per Element

8

High Level Output Current

High-level Output Current IOH The current flowing into the output at a specified high- level voltage. Low-level Output Current IOL The current flowing into the output at a specified low- level output voltage.

12mA

Low Level Output Current

The current into the output terminal with input conditions applied that, according to the product specification, will establish a low level at the output.

12mA

Control Type

COMMON CONTROL

Translation

N/A

Length

12.5mm

Width

6.1mm

Thickness

1mm

Radiation Hardening

Radiation hardening is the process of making electronic components and circuits resistant to damage or malfunction caused by high levels of ionizing radiation, especially for environments in outer space (especially beyond the low Earth orbit), around nuclear reactors and particle accelerators, or during nuclear accidents or nuclear warfare.

No

RoHS Status

RoHS means “Restriction of Certain Hazardous Substances” in the “Hazardous Substances Directive” in electrical and electronic equipment.

RoHS Compliant

Lead Free

Lead Free